h*9
2 楼
做做停停,历时近4周的地板工程终于完工了,现在贴些图分享一下。
改造的是formal dinnering room, 面积不大,10'x12',但有一梯级和两柱子。选用的
木板是 3.25" wide, 0.75" thick 的 Bruce butterscrotch oak hardwood plank.
改造的是formal dinnering room, 面积不大,10'x12',但有一梯级和两柱子。选用的
木板是 3.25" wide, 0.75" thick 的 Bruce butterscrotch oak hardwood plank.
x*3
3 楼
没有人知道吗?
h*9
4 楼
第一件要做的事是掀地毯,同时用 painting drop cloth 将房间封起来,然后将四周
固定地毯的带钉木条撬起,将 carpet pad 拿走后就用钳将 subfloor 上的 staple 一
个一个拔掉。
固定地毯的带钉木条撬起,将 carpet pad 拿走后就用钳将 subfloor 上的 staple 一
个一个拔掉。
b*i
5 楼
你的问题太笼统,it really depends
h*9
6 楼
Prepare subfloor 这一步很重要,低补高磨。
n*7
7 楼
基本上都是。如果有不是的,lz找到了公布下。
h*9
8 楼
铺木地板时地板与墙应有 expansion gap,你在这里有两个选择:
1. 地板离墙0.5寸;
2. 将 drywall 割掉一些,地板与墙对齐。
我选的是#2,因为如果用#1,将来装 baseboard 的时候要用 quarter round 来将
expansion gap 盖住。
房间的一边墙原来已经离地,另外两边就没那么好运了。先用锯锯掉门框,再用
oscillating tool 将 drywall 割掉一些,离地稍比木地板高些。
1. 地板离墙0.5寸;
2. 将 drywall 割掉一些,地板与墙对齐。
我选的是#2,因为如果用#1,将来装 baseboard 的时候要用 quarter round 来将
expansion gap 盖住。
房间的一边墙原来已经离地,另外两边就没那么好运了。先用锯锯掉门框,再用
oscillating tool 将 drywall 割掉一些,离地稍比木地板高些。
h*9
10 楼
割墙的过程中有些意外,发现了一些黄黑色的小颗粒,google 了一下好象是白蚁屎!
! 赶紧将墙割一孔检查,里面也有一些,但没有白蚁,木头还好,可能以前
fumigation 时白蚁已经死翘翘了。检查完后就补墙。
! 赶紧将墙割一孔检查,里面也有一些,但没有白蚁,木头还好,可能以前
fumigation 时白蚁已经死翘翘了。检查完后就补墙。
h*9
11 楼
掀起地毯后发现梯级的地方还有一 stair nose, 还要费力撬掉,这该死的东西还钉得
特牢,只好用 circular saw 调好切割厚度,将其锯成几段,还要动用 reciprocal
saw 将它彻底锯断后撬掉。
特牢,只好用 circular saw 调好切割厚度,将其锯成几段,还要动用 reciprocal
saw 将它彻底锯断后撬掉。
h*9
12 楼
处理完 stair nose 后还要把 riser board 也干掉,然后将边角修修补补,铺上防潮纸
,量好距离,弹几条基准线。
,量好距离,弹几条基准线。
h*9
13 楼
到此为止 subfloor 终于最被好了,TMD 累死了。
开铺前先要决定木板的方向,原则是木条要和支撑 subfloor 的梁垂直。我的房间因为
有个梯级,要装 stair nose, 所以比较麻烦。 Lowes 的 flooring manager 告诉我很
多 contractor 先装 stair nose, 然后从那往里面铺,另一人却说可以量好尺寸,从
里往外铺,最后才装 stair nose. 第一种方法比较好控制,但要多 face nail 一排,
而且要转向 ( first row's tongue faces outside. use a spline to connect the
grooves between first and second rows so that second row's tongue will face
inside.), 所以我决定用第二种方法。
里面头两排因为不够地方用 nail gun, 所以要手工钉。选用最直最长的木条,第一排
predrill 3/32”, 用 6d finish nail 从上往下钉 (face nail). 第二排在 tongue
处 45 度方向钉 (blind nail).
开铺前先要决定木板的方向,原则是木条要和支撑 subfloor 的梁垂直。我的房间因为
有个梯级,要装 stair nose, 所以比较麻烦。 Lowes 的 flooring manager 告诉我很
多 contractor 先装 stair nose, 然后从那往里面铺,另一人却说可以量好尺寸,从
里往外铺,最后才装 stair nose. 第一种方法比较好控制,但要多 face nail 一排,
而且要转向 ( first row's tongue faces outside. use a spline to connect the
grooves between first and second rows so that second row's tongue will face
inside.), 所以我决定用第二种方法。
里面头两排因为不够地方用 nail gun, 所以要手工钉。选用最直最长的木条,第一排
predrill 3/32”, 用 6d finish nail 从上往下钉 (face nail). 第二排在 tongue
处 45 度方向钉 (blind nail).
h*9
14 楼
手工钉完头两排后就有足够的空间使用钉枪了,调好气压,先用一块木头测试钉的深度
,然后就一排一排的钉。钉的时候用锤敲打的力度要适中。
,然后就一排一排的钉。钉的时候用锤敲打的力度要适中。
h*9
15 楼
第一次做,出错难免。钉得不够深,用锤手工敲也敲不进去,只能将钉割断。最惨的是
钉歪了,地板表面损坏,要将其撬起。这个时候不能硬撬,要用 circular saw, 调好
切割深度,横切一刀,竖切一刀,然后再撬掉。
钉歪了,地板表面损坏,要将其撬起。这个时候不能硬撬,要用 circular saw, 调好
切割深度,横切一刀,竖切一刀,然后再撬掉。
h*9
16 楼
和厨房连接处要有一个 transition piece, 买的话很贵,而且厚度不一定合适,所以
就自己动手做一个。选用一条颜色深的,切好长度后用 table saw 切去一角,怎么样
,还不错吧?
就自己动手做一个。选用一条颜色深的,切好长度后用 table saw 切去一角,怎么样
,还不错吧?
h*9
17 楼
快要完工了,两个小领导开着车到施工现场来视察,这里今后就是他们学爬之地。
h*9
18 楼
最后就是装 stair nose 了,一条不够长,要用两条,连接处本来可以一刀切,但不知
我当时为什么突发奇想,要搞些花样。第一条要切掉整个边角,很容易,第二条只切一
角,没有 router, 要手工操作,用锯和 Dremel tool 折腾一番后猛然想起这个法宝
才是正确工具。
我当时为什么突发奇想,要搞些花样。第一条要切掉整个边角,很容易,第二条只切一
角,没有 router, 要手工操作,用锯和 Dremel tool 折腾一番后猛然想起这个法宝
才是正确工具。
h*9
19 楼
这个 Rockwell Blade Runner 这次也功不可没。Stair nose 装完后就这样子。
h*9
20 楼
最后装上 baseboard,用 wood filler 填钉孔,大功告成了!!
h*9
22 楼
这次工程动用了本人几乎所有的工具。
写完了,多谢捧场,请多指教。
写完了,多谢捧场,请多指教。
R*R
23 楼
超强。
只有给自己干才会这么认真。
赞。
只有给自己干才会这么认真。
赞。
S*s
24 楼
Zan!
j*o
25 楼
膜拜大牛
做做停停,历时近4周的地板工程终于完工了,现在贴些图分享一下。
改造的是formal dinnering room, 面积不大,10'x12',但有一梯级和两柱子。选用的
木板是 3.25" wide, 0.75" thick 的 Bruce butterscrotch oak hardwood plank.
【在 h**********9 的大作中提到】
: 做做停停,历时近4周的地板工程终于完工了,现在贴些图分享一下。
: 改造的是formal dinnering room, 面积不大,10'x12',但有一梯级和两柱子。选用的
: 木板是 3.25" wide, 0.75" thick 的 Bruce butterscrotch oak hardwood plank.
做做停停,历时近4周的地板工程终于完工了,现在贴些图分享一下。
改造的是formal dinnering room, 面积不大,10'x12',但有一梯级和两柱子。选用的
木板是 3.25" wide, 0.75" thick 的 Bruce butterscrotch oak hardwood plank.
【在 h**********9 的大作中提到】
: 做做停停,历时近4周的地板工程终于完工了,现在贴些图分享一下。
: 改造的是formal dinnering room, 面积不大,10'x12',但有一梯级和两柱子。选用的
: 木板是 3.25" wide, 0.75" thick 的 Bruce butterscrotch oak hardwood plank.
m*f
26 楼
赞顶膜拜
z*9
27 楼
great job! Thanks for sharing, will keep it.
l*o
28 楼
崇拜呀
s*d
29 楼
这个实在是太牛了
楼主工具很齐全,能不能介绍一下?想搞个简单的workshop, 弄点简单的木工、修修补
补什么的,但是市面上的工具琳琅满目,看得是一头雾水。楼主要是能贴个经验心得就
好了,造福一下DIY新手
不情之请,楼主莫怪
楼主工具很齐全,能不能介绍一下?想搞个简单的workshop, 弄点简单的木工、修修补
补什么的,但是市面上的工具琳琅满目,看得是一头雾水。楼主要是能贴个经验心得就
好了,造福一下DIY新手
不情之请,楼主莫怪
t*g
30 楼
http://www.prettyhandygirl.com/my-toolbox
地板,如果是pre-finish的话很简单的。你找人做也不贵,我们这里大概$1/sqft的人
工费。
【在 s*******d 的大作中提到】
: 这个实在是太牛了
: 楼主工具很齐全,能不能介绍一下?想搞个简单的workshop, 弄点简单的木工、修修补
: 补什么的,但是市面上的工具琳琅满目,看得是一头雾水。楼主要是能贴个经验心得就
: 好了,造福一下DIY新手
: 不情之请,楼主莫怪
地板,如果是pre-finish的话很简单的。你找人做也不贵,我们这里大概$1/sqft的人
工费。
【在 s*******d 的大作中提到】
: 这个实在是太牛了
: 楼主工具很齐全,能不能介绍一下?想搞个简单的workshop, 弄点简单的木工、修修补
: 补什么的,但是市面上的工具琳琅满目,看得是一头雾水。楼主要是能贴个经验心得就
: 好了,造福一下DIY新手
: 不情之请,楼主莫怪
s*z
31 楼
太牛了!!!
g*x
33 楼
强人, 很漂亮啊
H*7
35 楼
收藏
s*d
36 楼
多谢,收藏了
现在倒是没有做地板的打算,只是想搭个workshop,先买点工具
【在 t****g 的大作中提到】
: http://www.prettyhandygirl.com/my-toolbox
: 地板,如果是pre-finish的话很简单的。你找人做也不贵,我们这里大概$1/sqft的人
: 工费。
现在倒是没有做地板的打算,只是想搭个workshop,先买点工具
【在 t****g 的大作中提到】
: http://www.prettyhandygirl.com/my-toolbox
: 地板,如果是pre-finish的话很简单的。你找人做也不贵,我们这里大概$1/sqft的人
: 工费。
I*M
37 楼
膜拜一下双宝爹。你那个living/family room是sunken的么?有没有想改造一下,这
样以后对小朋友们安全一点?
样以后对小朋友们安全一点?
u*q
38 楼
非常崇拜。
h*9
39 楼
材料:
1. Hard wood floor planks: 7 boxes,6.25 boxes actually used, 22 sqft per
box, $107 x 7 = $749
2. Stair nose pieces: $50 x 2 = $100
3. Floor nails: 1 box (1000 nails) $20
4. Finish nails: 1 box $7
5. Staples
6. Wood glue
7. Moulding: 2 16' base boards $12 + some left over from previous project
6. 垫子是用修白菜房剩下的防潮纸,忘记价钱了。
工具本来就有了,floor nailer 用完退掉。
耗时可能超过40小时。第一次做没经验,做得很慢,过分节省木料,而且没有将所有木
板按长短分组排序,花了太多时间在挑选木板,另外都在车库锯,来回走很费时。
【在 c******z 的大作中提到】
: 非常详细的资料!!
: 可以请问材料(地板本身、边边角角、垫子等)以及工具的花费吗?
: 另外大概实际的工程耗时是(20小时?40小时?)?
h*9
40 楼
$1/sqft 是 laminate 吧?
【在 t****g 的大作中提到】
: http://www.prettyhandygirl.com/my-toolbox
: 地板,如果是pre-finish的话很简单的。你找人做也不贵,我们这里大概$1/sqft的人
: 工费。
e*t
41 楼
楼主,你做的太认真了。找人做是做不了这么细致的,地面整平和割drywall都不会给
你做的,所以diy还是值得的。好多问题我也遇到过,包括钉子钉了一半的情况,大多
数我还是拿nail set打进去了。我也没作地面整平,只是在有声音的subfloor上加了螺
钉。我做的形状比你这个复杂,无数条边,烦死个人。
你做的,所以diy还是值得的。好多问题我也遇到过,包括钉子钉了一半的情况,大多
数我还是拿nail set打进去了。我也没作地面整平,只是在有声音的subfloor上加了螺
钉。我做的形状比你这个复杂,无数条边,烦死个人。
T*U
43 楼
不是说地板木条走向得向着窗户吗?
D*r
44 楼
不得不顶,太强了!
h*8
45 楼
牛!收藏
w*5
53 楼
收藏,很漂亮,谢谢分享
r*n
57 楼
$1/sqft hard wood floor,咋么可能,咋么可能?
e*t
58 楼
友情帮顶楼主。
贴的图就是我前面说的自己做的痛不欲生的木地板,主要是很多个边/交界。下图左边
是单独看地板的形状。
为啥不全做成地板的?因为穷。
贴的图就是我前面说的自己做的痛不欲生的木地板,主要是很多个边/交界。下图左边
是单独看地板的形状。
为啥不全做成地板的?因为穷。
t*r
71 楼
很漂亮
u*q
73 楼
大牛,请问:
1) Do you find the table saw scary to use? I heard it is the single most
dangerous tool for the average homeowner.
2) That BladeRunner looks like a band saw. I have never seen it on the to-
buy list for homeowners. For what project did you buy it?
3) Which other projects did you tackle before this one? //admire
【在 h**********9 的大作中提到】
:
: 你在哪买的?我是在 Lowes 进的货, 地板是 4.99 一尺,用 coupon 减了 10%.
1) Do you find the table saw scary to use? I heard it is the single most
dangerous tool for the average homeowner.
2) That BladeRunner looks like a band saw. I have never seen it on the to-
buy list for homeowners. For what project did you buy it?
3) Which other projects did you tackle before this one? //admire
【在 h**********9 的大作中提到】
:
: 你在哪买的?我是在 Lowes 进的货, 地板是 4.99 一尺,用 coupon 减了 10%.
h*9
74 楼
most
Yes, table saw is dangerous. I still remember when I used it for the
first time, I was very scared. I am still very careful when using it
now. Always keep your hands far away from the saw blade. Use a wood
stick to push the wood being cut. And sometimes the cut out piece will
get knocked back. So stand a little off the feeding direction.
to-
I picked up the BladeRunner on black Friday. It's kind of a hybrid of a
scroll saw and jig saw. And it can be use as miter saw and table saw to
some degree. It's very good to cut thin and soft stuffs but hard to cut
things more than 1 inch thick. It also came with a tile blade and can
cut ceramic and porcelain tiles. I bought it because I didn't have jig
saw and tile saw. Because it's very light and easy to carry, I can use
it to repair rental properties.
Not a lot of big projects. Installing laminate floor; adding interior
walls; changing interior doors (prehung); some moulding works; garage
door openner; finishing garage wall; rewiring garage; installing vinyl
gutter; dry wall repair and painting; changing faucets, etc.
【在 u****q 的大作中提到】
: 大牛,请问:
: 1) Do you find the table saw scary to use? I heard it is the single most
: dangerous tool for the average homeowner.
: 2) That BladeRunner looks like a band saw. I have never seen it on the to-
: buy list for homeowners. For what project did you buy it?
: 3) Which other projects did you tackle before this one? //admire
y*3
77 楼
one common mistake, most people think quarter round is for cover nail holes,
and lot people don't use them. both baseboard and quarter round are used to
cover up imperfections along two directions, base board will cover up and
downs along the wall and quarter round will cover high and lows along the
floor.
and lot people don't use them. both baseboard and quarter round are used to
cover up imperfections along two directions, base board will cover up and
downs along the wall and quarter round will cover high and lows along the
floor.
u*q
78 楼
牛啊牛啊牛啊牛啊牛啊牛啊
【在 h**********9 的大作中提到】
:
: most
: Yes, table saw is dangerous. I still remember when I used it for the
: first time, I was very scared. I am still very careful when using it
: now. Always keep your hands far away from the saw blade. Use a wood
: stick to push the wood being cut. And sometimes the cut out piece will
: get knocked back. So stand a little off the feeding direction.
: to-
: I picked up the BladeRunner on black Friday. It's kind of a hybrid of a
: scroll saw and jig saw. And it can be use as miter saw and table saw to
【在 h**********9 的大作中提到】
:
: most
: Yes, table saw is dangerous. I still remember when I used it for the
: first time, I was very scared. I am still very careful when using it
: now. Always keep your hands far away from the saw blade. Use a wood
: stick to push the wood being cut. And sometimes the cut out piece will
: get knocked back. So stand a little off the feeding direction.
: to-
: I picked up the BladeRunner on black Friday. It's kind of a hybrid of a
: scroll saw and jig saw. And it can be use as miter saw and table saw to
w*D
81 楼
好贴,学习了
a*o
82 楼
同学门要不要这么能干呀
相关阅读
求教暖水的water pump不停急问:灶台不打火了怎么修?大家用没有长柄的炒锅吗向保险公司claim换屋顶需要问些什么问题?TWC的生意火爆啊Share cell phone family planinvestment condo owner occupancy is 〈51%现在冬天院子里需要做什么?costco的这个gas cooktop怎样?死过人的房子怎么样?新房子舍不得往墙上打钉子发现清理炉台有个好东西版主新年好,啥时候发2015新年包子啊Pyrex的盖子破了有什么好办法?娇娇铁钉团申请几个月了,也没人给个准信?what is your new year resolution?[活动]:我家的2014DIYs 总结:)How often do you empty septic tanks?怎么找不到华人师傅做庭院?我要中了,怎么办