a*a
2 楼
旧餐桌面斜看的话惨不忍睹，各位有没有refinish过clear coat?
z*9
3 楼
从myfurnitureforum上copy过来的。
Go to the store and buy the following (you may have to get some of this on-
line):
* 1 spray can heavy bodied sanding sealer
* 2 spray cans of either gloss or satin Lacquer (depending on the sheen you
want, or you can get one of each)
* Some furniture markers in the color of your desk wood, can be darker but
not lighter
* 150 and 220 grit and 600 grit sandpaper.
* 0000 Steel Wool
* Mineral Spirits.
Procedure:
1) Wipe down the whole desk with mineral spirits. Get all the old gunk off.
2) Steel wool the top to level it, stay with the grain.
3) Color in any bare wood with the markers, smudge it with your fingers,
then wool it down.
4) Take your sanding sealer and make sure its shaken well so it doesn't '
spit' from the nozzle. Lay sanding sealer on the top, spraying more into
nicks and scratches as needed. This will dry fast (about 15 minutes for a
moderate coat). Do not sand until its dry. Once it is dry, use your 150 grit
to sand over the depression areas and a light general sanding over the
whole top. LIGHT ON THE WHOLE TOP! Do another layer and sanding on
depressions, repeat until the depressions are filled and level with the desk
top. Sometimes this can take up to 10 coats or more. Keep at it, and sand
it down without breaking through to the color coat. No need to dust off the
sanding sealer, just spray over the stuff you just sanded.
5) Once you get the top leveled and smooth with the sealer, then sand with
220. Do not sand in arcs, keep it straight with the grain. Dust off and wipe
down when done.
6) Now you do your clears. Take TWO cans of the lacquer, well shaken so they
don't spit,and with one in each hand spray them at the same time moving
your body, not swinging the cars in an arc. Cross the streams when you spray
. This gives you the equal of a spray gun finish. Just one can will leave
valleys in the finish. Let this dry to a hard finish, at least 1 hour. Wet
sand to 600 grit and then do it again. When done the second time, wool the
table with # 0000 Steel wool and then follow with a good coat of paste wax.
You're done!
Go to the store and buy the following (you may have to get some of this on-
line):
* 1 spray can heavy bodied sanding sealer
* 2 spray cans of either gloss or satin Lacquer (depending on the sheen you
want, or you can get one of each)
* Some furniture markers in the color of your desk wood, can be darker but
not lighter
* 150 and 220 grit and 600 grit sandpaper.
* 0000 Steel Wool
* Mineral Spirits.
Procedure:
1) Wipe down the whole desk with mineral spirits. Get all the old gunk off.
2) Steel wool the top to level it, stay with the grain.
3) Color in any bare wood with the markers, smudge it with your fingers,
then wool it down.
4) Take your sanding sealer and make sure its shaken well so it doesn't '
spit' from the nozzle. Lay sanding sealer on the top, spraying more into
nicks and scratches as needed. This will dry fast (about 15 minutes for a
moderate coat). Do not sand until its dry. Once it is dry, use your 150 grit
to sand over the depression areas and a light general sanding over the
whole top. LIGHT ON THE WHOLE TOP! Do another layer and sanding on
depressions, repeat until the depressions are filled and level with the desk
top. Sometimes this can take up to 10 coats or more. Keep at it, and sand
it down without breaking through to the color coat. No need to dust off the
sanding sealer, just spray over the stuff you just sanded.
5) Once you get the top leveled and smooth with the sealer, then sand with
220. Do not sand in arcs, keep it straight with the grain. Dust off and wipe
down when done.
6) Now you do your clears. Take TWO cans of the lacquer, well shaken so they
don't spit,and with one in each hand spray them at the same time moving
your body, not swinging the cars in an arc. Cross the streams when you spray
. This gives you the equal of a spray gun finish. Just one can will leave
valleys in the finish. Let this dry to a hard finish, at least 1 hour. Wet
sand to 600 grit and then do it again. When done the second time, wool the
table with # 0000 Steel wool and then follow with a good coat of paste wax.
You're done!
z*9
4 楼
我根据上面的instruction做过，有比较成功的，也有失败的。失败的原因可能是旧的
clear coat清理的不干净，也可能是某些地方喷的太多，反正结果是起橘皮，只好重做
。
我也请人做过，一个很大的council desk，450刀。但是效果不太满意，主要是clear
coat只上了3层。要做出council原厂出来的效果至少10层。不过450也不可能要求那么
多了。
clear coat清理的不干净，也可能是某些地方喷的太多，反正结果是起橘皮，只好重做
。
我也请人做过，一个很大的council desk，450刀。但是效果不太满意，主要是clear
coat只上了3层。要做出council原厂出来的效果至少10层。不过450也不可能要求那么
多了。
H*s
5 楼
Sounds fun
you
【在 z***9 的大作中提到】
: 从myfurnitureforum上copy过来的。
: Go to the store and buy the following (you may have to get some of this on-
: line):
: * 1 spray can heavy bodied sanding sealer
: * 2 spray cans of either gloss or satin Lacquer (depending on the sheen you
: want, or you can get one of each)
: * Some furniture markers in the color of your desk wood, can be darker but
: not lighter
: * 150 and 220 grit and 600 grit sandpaper.
: * 0000 Steel Wool
you
【在 z***9 的大作中提到】
: 从myfurnitureforum上copy过来的。
: Go to the store and buy the following (you may have to get some of this on-
: line):
: * 1 spray can heavy bodied sanding sealer
: * 2 spray cans of either gloss or satin Lacquer (depending on the sheen you
: want, or you can get one of each)
: * Some furniture markers in the color of your desk wood, can be darker but
: not lighter
: * 150 and 220 grit and 600 grit sandpaper.
: * 0000 Steel Wool
a*a
6 楼
谢谢步骤，目前先用bee wax打亮了点，下次先在一个椅子上练手后再试桌子
【在 z***9 的大作中提到】
: 我根据上面的instruction做过，有比较成功的，也有失败的。失败的原因可能是旧的
: clear coat清理的不干净，也可能是某些地方喷的太多，反正结果是起橘皮，只好重做
: 。
: 我也请人做过，一个很大的council desk，450刀。但是效果不太满意，主要是clear
: coat只上了3层。要做出council原厂出来的效果至少10层。不过450也不可能要求那么
: 多了。
【在 z***9 的大作中提到】
: 我根据上面的instruction做过，有比较成功的，也有失败的。失败的原因可能是旧的
: clear coat清理的不干净，也可能是某些地方喷的太多，反正结果是起橘皮，只好重做
: 。
: 我也请人做过，一个很大的council desk，450刀。但是效果不太满意，主要是clear
: coat只上了3层。要做出council原厂出来的效果至少10层。不过450也不可能要求那么
: 多了。
h*z
7 楼
这个refinish橱柜的套装不需要sand，据说比较容易成功，我们可否自己按照里面的东
西自己配
http://www.amazon.com/exec/obidos/ASIN/B006Z6ADT6/1-b003homep2-
应该会便宜一些
【在 a********a 的大作中提到】
: 谢谢步骤，目前先用bee wax打亮了点，下次先在一个椅子上练手后再试桌子
西自己配
http://www.amazon.com/exec/obidos/ASIN/B006Z6ADT6/1-b003homep2-
应该会便宜一些
【在 a********a 的大作中提到】
: 谢谢步骤，目前先用bee wax打亮了点，下次先在一个椅子上练手后再试桌子
z*9
8 楼
it all depends how good and durable the final finish you want. the
traditional method yield the best result, but time consuming. new tech gives
you an opportunity to diy in an easier way, but the finish might be lousy.
for fine furniture, i will seek the best way to do, for something temporary
these kits may work.
traditional method yield the best result, but time consuming. new tech gives
you an opportunity to diy in an easier way, but the finish might be lousy.
for fine furniture, i will seek the best way to do, for something temporary
these kits may work.
h*z
9 楼
多谢
gives
.
temporary
【在 z***9 的大作中提到】
: it all depends how good and durable the final finish you want. the
: traditional method yield the best result, but time consuming. new tech gives
: you an opportunity to diy in an easier way, but the finish might be lousy.
: for fine furniture, i will seek the best way to do, for something temporary
: these kits may work.
gives
.
temporary
【在 z***9 的大作中提到】
: it all depends how good and durable the final finish you want. the
: traditional method yield the best result, but time consuming. new tech gives
: you an opportunity to diy in an easier way, but the finish might be lousy.
: for fine furniture, i will seek the best way to do, for something temporary
: these kits may work.
相关阅读
房客抽大麻怎么办？养孩子的意义到底在哪里邻居Condo失火，我的CONDO保险过期了，那我的损失可以找邻居保美国锈带的一个小镇厨房不靠外墙，想装神器是屋顶打洞还是从阁楼拐弯去外墙？最近有冰箱的deal吗投资的第五套房落听，不知道一家或者一个人最多能贷几套？请教，地下室装什么地板好？请问能不能把卧室屋顶的电风扇换成flush mount的灯？前房主之一得重病死亡，房子被flipper推倒重盖moisture barrier下面会不会发霉的啊？木头门上的钉孔用什么补关于游泳池遇到烂房客，怎么办？在Amazon购物时候会向卖家要code或者免费测评吗？厨房抽油烟机这个梯子怎样？黄蚂蚁吃白蚁？无标题看上去的老房子毛病较多。 会影响办贷款吗 (转载)